You can upgrade from Emissary-ingress to Ambassador Edge Stack with a few simple commands. When you upgrade to Ambassador Edge Stack, you'll be able to access additional capabilities such as automatic HTTPS/TLS termination, Swagger/OpenAPI support, API catalog, Single Sign-On, and more. For more about the differences between Ambassador Edge Stack and Emissary-ingress, see the Editions page.
The recommended strategy for migration is to run Emissary-ingress 3.1.0 and Ambassador Edge Stack 3.1.0 side-by-side in the same cluster. This gives Ambassador Edge Stack 3.1.0 and Ambassador Edge Stack 3.1.0 access to all the same configuration resources, with some important notes:
If needed, you can use labels to further isolate configurations.
If you need to prevent your Ambassador Edge Stack 3.1.0 installation from seeing a particular bit of Emissary-ingress 3.1.0 configuration, you can apply a Kubernetes label to the configuration resources that should be seen by your Ambassador Edge Stack 3.1.0 installation, then set its
AMBASSADOR_LABEL_SELECTORenvironment variable to restrict its configuration to only the labelled resources.
For example, you could apply a
version-two: truelabel to all resources that should be visible to Ambassador Edge Stack 3.1.0, then set
AMBASSADOR_LABEL_SELECTOR=version-two=truein its Deployment.
Ambassador Edge Stack ACME and
Filters will be disabled while Emissary-ingress is still running.
Since Ambassador Edge Stack and Emissary-ingress share configuration, Ambassador Edge Stack cannot configure its ACME or other filter processors without also affecting Emissary-ingress. This migration process is written to simply disable these Ambassador Edge Stack features to make it simpler to roll back, if needed. Alternate, you can isolate the two configurations as described above.
Be careful to only have one Ambassador Edge Stack Agent running at a time.
The Ambassador Edge Stack Agent is responsible for communications between Ambassador Edge Stack and Ambassador Cloud. If multiple versions of the Agent are running simultaneously, Ambassador Cloud could see conflicting information about your cluster.
The best way to avoid multiple agents when installing with Helm is to use
--set emissary-ingress.agent.enabled=falseto tell Helm not to install a new Agent with Ambassador Edge Stack 3.1.0. Once testing is done, you can switch Agents safely.
Be careful about label selectors on Kubernetes Services!
If you have services in Emissary-ingress 3.X that use selectors that will match Pods from Ambassador Edge Stack 3.1.0, traffic will be erroneously split between Emissary-ingress 3.X and Ambassador Edge Stack 3.1.0. The labels used by Ambassador Edge Stack 3.1.0 include:
You can also migrate by installing Ambassador Edge Stack 3.1.0 in a separate cluster. This permits absolute certainty that your Emissary-ingress 3.1.0 configuration will not be affected by changes meant for Ambassador Edge Stack 3.1.0, but it is more effort.
Migration is a six-step process:
Install new CRDs.
Before installing Ambassador Edge Stack 3.1.0 itself, you need to update the CRDs in your cluster; Helm will not do this for you. This is mandatory during any upgrade of Ambassador Edge Stack.
Install Ambassador Edge Stack 3.1.0.
After installing the new CRDs, you need to install Ambassador Edge Stack 3.1.0 itself in the same namespace as your existing Emissary-ingress 3.1.0 installation. It's important to use the same namespace so that the two installations can see the same secrets, etc.
Start by making sure that your
datawireHelm repo is set correctly:
Typically, Emissary-ingress 3.1.0 was installed in the
emissarynamespace. If you installed Emissary-ingress 3.1.0 in a different namespace, change the namespace in the commands below.
If you do not need to set
If you do need to set
--set, for example:
Your Ambassador Edge Stack 3.1.0 installation should come up running with the configuration resources used by Emissary-ingress 3.1.0, including
If you find that you need to roll back, just reinstall your Emissary-ingress 3.1.0 CRDs and delete your installation of Ambassador Edge Stack 3.1.0.
When ready, switch over to Ambassador Edge Stack 3.1.0.
You can run Emissary-ingress 3.1.0 and Ambassador Edge Stack 3.1.0 side-by-side as long as you care to. When you're ready to have Ambassador Edge Stack 3.1.0 handle traffic on its own, switch your original Emissary-ingress 3.1.0 Service to point to Ambassador Edge Stack 3.1.0. Use
kubectl edit -n emissary service emissary-ingressand change the
kubectl edit service ambassador-adminfor the
Install the Ambassador Edge Stack 3.1.0 Ambassador Agent.
First, scale the Emissary-ingress agent to 0:
Once that's done, install the new Agent:
Finally, enable ACME and filtering in Ambassador Edge Stack 3.1.0.
First, scale the Emissary-ingress Deployment to 0:
Once that's done, enable ACME and filtering in Ambassador Edge Stack 3.1.0:
Congratulations! At this point, Ambassador Edge Stack 3.1.0 is fully running, and
it's safe to remove the old
You may also want to redirect DNS to the
edge-stack Service and remove the